The main fusion welding can weld copper, brass, bronze, copper, copper clad steel, made of iron, stainless steel, wrought iron, galvanized steel, cast iron, copper alloys, steel and other materials. There are eight kinds of fusion welding forms, wire and wire welding, wire and metal strip (band) welding wire and ground rod (pole) welding, metal plates and wires are connected to the metal strip (strip) with the metal strip (band) welding, metal strip (strip) and ground rod (pole) welding, metal strip (band) and the metal plate welding, metal rods and metal plates welded. Each contains a different type of connection in the form of welding wire and the welding wire has a butt, cross, connected in parallel, T-shaped connections, etc., of various forms of well completion of welding. Fusion welding is widely used in power plants, substations, transmission line towers, communication base stations, airports, railways, a variety of high-rise buildings, microwave relay stations, network room, petrochemical plants, oil storage facilities and other places of lightning protection and grounding, anti-static grounding, protection welding ground, ground work and the like. Connected to a hot-melt welding product applications, and network level connection 2, the signal line and the three oil and gas pipelines, and rail signal lines 4, 5 and steel, lead and terminals 6, other electrical connections fusion welding Notes 1, First 2 fusion welding, before welding to pull pieces of processed according to the shape and size connector, issued a suitable mold, and configure the appropriate type of solder powder, oil, dirt and oxide layers in addition to 3, the mold is full of intense heat 4 After installing the solder powder is poured into a mold inspection and ignited reaction 5, the mold is cleaned and ready for the next use more products please visit: http: //www.btsjgy.com/rrhj/236.htm mold and mold clamp Prepare with points 1, before fusion welding tool using dried by heating the mold (such as drying oven or burners), get rid of moisture. From lack of use of the mold containing the water, especially after the previous use of any residue left in the mold, the water more. 2. Clean the mold, use a soft brush or other soft materials. 3. Check the contact surface of the mold adaptation, prevent job copper fluid leakage from the crevice. 4, mold clamp is used for opening and closing the mold, mold clamp tightness influential effect on welding, please check carefully before you start welding mold folder and make appropriate adjustments. 5. Install the adjusting mold clip, clip adaptation will die and mold adaptation to adjust to the best state. Adjusted as follows: a) the mold open state or position sandwiched b) Loosen the clamp die tied to catch (1) c) Remove the fixed tie (2) d) adjusting the adjusting screw (3) counter-clockwise (loosen) e) insert fixed tied with lock f) opening the clamping clip, the observed effect. Prepare the mold and die with points of a clip before fusion welding tool using dried by heating the mold (such as drying box or burner), get rid of moisture. From lack of use of the mold containing the water, especially after the previous use of any residue left in the mold, the water more. 2. Clean the mold, use a soft brush or other soft materials. 3. Check the contact surface of the mold adaptation, prevent job copper fluid leakage from the crevice. 4, mold clamp is used for opening and closing the mold, mold clamp tightness influential effect on welding, please check carefully before you start welding mold folder and make appropriate adjustments. 5. Install the adjusting mold clip, clip adaptation will die and mold adaptation to adjust to the best state. Adjusted as follows: a) the mold open state or position sandwiched b) Loosen the clamp die tied to catch (1) c) Remove the fixed tie (2) d) adjusting the adjusting screw (3) counter-clockwise (loosen) e) insert fixed tied with lock f) opening the clamping clip, the observed effect. Repeat adjustment clip distance, until the mold and the mold clamp adaptation adaptation can match. If the mold opening and closing folders need to use a larger force, then clip to the best position from the unadjusted (clip from too short), the need to re-adjust. Installation and adjustment module folders have a major impact on the "hot pass" weld quality and service life of molds and mold clamp, so please carefully adjust the distance before fusing better. Whether or not there is the seal, improper clip from the clip will be on the mold and mold damage. (1) Fixed bolt lock (2) mounting pins (3) adjusting screw 6, wide source of exothermic welding mold made of graphite, is very fragile and can not withstand the impact slinger and strength, it can not be shown to exceed the size of the mold plate The fusion was forced into the mold, or using a metal material, hard tools to remove residue. 7, if the die plate is smaller than the size of the seal shown in order to avoid leakage of liquid copper following methods are available to make up :( pictured) 1) fusion welding using a sealant 2) using a high temperature cotton belt 8, graphite mold as described above Step maintenance, service life of up to 50 to 100 times.